Itron Cellular 500W Module in Network Mode Check Endpoint Status Response Fields

This section describes the Itron Cellular 500W Module Check Endpoint response fields for Check Endpoint Status, FWDL Status, and Check Firmware Versions.

Response Field	Description
Endpoint Id	The endpoint’s device identification number.
Endpoint Reading	The meter reading as reported by the endpoint. If the endpoint reading value is underlined, you must click the value to format the read. For more information, see Formatting Gas and Electric Endpoint Readings.
Backflow Register	The current reading of the meter's backflow consumption register. The reading indicates the total backflow that has passed through the meter since its manufacture.
Active Events	The number of events that were active at the time of the Check Endpoint operation. The field name is a hyperlink that opens a list of the meter's tampers. See Endpoint Tamper/Event Code Descriptions for descriptions of the events.
Device Type	The endpoint model (Itron Cellular 500W Module).
Device Sub Type	The endpoint model subtype: Remote. The device is a remote-mount ERT
Encoder Driver Type	The version number of the module's encoder driver, which is used to decode register data.
Register Type	May be either of the following values: Encoder Pulser
Programmed Meter Configuration	The meter's current programmed meter configuration. The field name is a hyperlink that opens the meter configuration log. Evaluate the values in the meter configuration log to audit the FSR who installed the endpoint. The meter configuration log provides: Unix time. The time the parameter was programmed. Parameter. The name of the parameter that was programmed. Programmed Value. The value that was programmed. Display value. The text displayed in the user interface for the parameter.
Truncation	The number of least-significant (rightmost) digits (0-3) by which the module is programmed to truncate the meter reading. This value is required to prevent high-resolution readings recorded by nine-dial water registers from overflowing the ERT module's datalogging buckets. The overflow potential pertains primarily to commercial accounts that consume high volumes of water.
Count Rate	The metrology value used with PCOMP, rollover, and counts to calculate the consumption value. Count Rate is displayed only if FDM is unable to determine the meter configuration. If you were not required to enter the meter's number of dials and billing units during the Check Endpoint workflow, then Count Rate is not returned in the Check Endpoint response.
Roll Over	The maximum possible meter reading before the dials roll over to zero. The number of nines shown in this field corresponds to the number of meter dials. This setting is used with PCOMP, count rate, and counts to calculate the consumption value.
PCOMP	The pressure compensation value programmed into the endpoint to compensate for the effect of atmospheric pressure on recorded consumption. None. The endpoint is not configured for pressure compensation
Battery Status	The state of the endpoint battery's electrical charge. Good. The battery's charge is greater than 10 percent of capacity. Bad. the battery's charge is at 10 percent or less of capacity.
Cut Threshold	How often, in hours, the endpoint checks to determine if the cable has been cut.
SSID	Reserved for future use.
Time Drift	The number of hours/min/sec that the endpoint time has drifted from the network time.
Configuration Tag	The name of the configuration file loaded to the device.
Registration Status Bits	Indicates whether the endpoint is registered successfully. Lists any of the following that are true: Endpoint Functions Correctly Operations Manager Connected Multicast Addresses Written The field name is a hyperlink that opens Registration Status Bits, where you can view more details.
Reverse Period	How long the endpoint will indicate a reverse flow tamper after a reverse flow occurs, as defined by the reverse threshold. For example, assume the Reverse Period value is 960 (40 days) and the Reverse Threshold value is 0. In this case, if the endpoint detects at least one reverse pulse during any one-hour period, it indicates a reverse flow tamper for 40 days. After 40 days without detecting a tamper, the endpoint resets the tamper flag. The default Reverse Period value is 960.
Reverse Threshold	The number of meter reverse pulses per hour during the reverse period that the endpoint uses to identify a reverse flow. If the number of reverse pulses per hour during the period specified in the Reverse Period field is greater than the Reverse Threshold value, the endpoint indicates a reverse flow. If the number of reverse pulses per hour during this period is less than or equal to the Reverse Period value, the endpoint does not indicate a reverse flow.
Leak Sensor Firmware Version	The current firmware version attached to the leak sensor.
Leak Sensor Hardware Version	The current hardware version of the leak sensor.
Leak Sensor Serial Number	The serial number associated with the leak sensor.
Leak Sensor Connection Status	Indicates whether the leak sensor is currently connected successfully or now: Connected Not connected
Leak Period	The number of hours that can pass before reporting a water leak.
Leak Threshold	The number of hours the leak report is maintained.
Firmware Version	The meter register firmware's version number.
Number of FWDL Initiated	The number of firmware download (FWDL) operations that have been initiated in the endpoint.
Sample Width	The sample width parameter.
Sample Rate	The sample rate parameter.
High Debounce Sample Rate	The sample rate with high debounce.
High Debounce Count	The count with high debounce.
Low Debounce Sample Rate	The sample rate with low debounce.
Low Debounce Count	The count with low debounce.
CE Address Index	The current CE address offset index.
NMS Address Index	The current NMS address offset index.