Intelis Gas Meter Events

No communication with register.

Note: For the Intelis Gas meter, this corresponds to the "Loss of Meter Communication" tamper bit in Mobile mode which could indicate the index has been removed from the meter.

The ERT has detected an external magnetic field.

The ERT has a low battery warning. 10% of battery life remains.

The ERT has detected reverse flow.

The ERT has detected the end of reverse flow after having reported reverse flow.

The ERT detects that a remote disconnect valve is attached and it is working properly (triggered when state was previously unknown or previously not working properly).

The ERT detects a remote disconnect valve is attached but it is not working properly.

The ERT detects consumption has exceeded the high flow threshold.

The ERT detects that consumption has dropped below the high flow threshold after having been in a high flow state.

The device detects that the temperature has exceeded the high temperature threshold.

The device detects that the temperature has dropped below the high temperature threshold after having been in a high temperature state.

The device detects air in the meter, possibly due to the meter being removed from the installation.

The device no longer detects air in the meter.

A critical internal error not described by other events.

A flash error has been detected.

Occurs when the ERT gets pulses or detects consumption for the first time.

The device has been changed to OpenWay Riva network mode.

Any change to the BatteryUseParameters structure results in this event.

The key has been updated in the device.

The application has not received any incoming data which indicates that the device may not be communicating on the network.

The load profile object has been cleared.

The time has been changed manually.

This event occurs when the Legally Relevant log is at 90% of its total capacity.

A time change greater than the warning level threshold has been detected.

A time change greater than the warning level threshold has ended and is back below the threshold.

The device has been changed from OpenWay Riva network mode to 100S mode.

The device has entered prover mode.

The device has exited prover mode.

The valve is in a disconnected state but flow has been detected by the device.

Note: This event does not have an end event but is debounced every 24 hours. So, for a device that is continually in this state, the event will be logged once every 24 hours.

The device push button has been depressed causing the LCD to turn on.

Note: This event is logged once each time the LCD is turned on, subsequent button pushes while the LCD is still on will not result in additional events being logged.

The device has detected that its flow sensor has failed. An ultrasonic measurement unit (UMU) hard error. This is an unrecoverable error.

The device has detected that the flow is outside the physical range of the measurement sensor. Qmin or Qmax exceeded.

The device has detected that the flow has returned to a level within the physical range of the measurement sensor after having been outside the range.

The device has detected that the gas temperature is outside the range of the temperature sensor (temperature max exceeded, temperature min exceeded).

The device has detected that the gas temperature has returned to a value within the range of the temperature sensor after having been outside the range.

The device has detected that a flow sensor measurement error has occurred. This is an unrecoverable error.

The device has detected that its ultrasonic transducers have an issue which is reflected by an abnormal gain or an abnormal Tup/Tdown (time required by the ultrasonic signal from the emitter to the receiver). This is an unrecoverable error.

The OpenWay Operations Center (OWCM) configuration in the device has changed.

The Itron event log has been reset.

A new configuration has been downloaded.

A watchdog error. Reboot.

A planned restart of ERT (for example, after firmware download).

The ERT could not adopt configuration information.

The disconnect command was received and has completed.

The disconnect command was received but failed to execute. The event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The ARM (for reconnect) command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received and has completed. Event detail will contain the verbose_result attribute of the DisconnectControl object.

The reconnect command was received but failed to execute. Event detail will contain the verbose_result attribute of the DisconnectControl object.

An application level security failure - authentication.

This event occurs with an application level security failure for authentication.

An application level security failure - access control.

This event occurs with an application level security failure for access control.

A key rollover command received.

An application level security failure - certificate.

A takeover package was presented and accepted by the ERT.

A takeover package was presented, but rejected by the ERT.

An application level security failure - replay.

A signed authorization with issued-to "Itron-RMA" has been received.

The valve actuation threshold has been exceeded. This will trigger at a count of 76 actuations for the Intelis Gas meter.

An override operation has occurred for this valve.

An auto disconnect occurred in the device.

A change has been made to the ProverModeMaximumTime.

A change has been made to the HighFlowSamplingConfiguation.

A change has been made to the HighTemperatureEventConfiguration.

The HighFlowDisconnectEnable configuration has changed.

The high temperature automatic disconnect configuration has changed.

The air in pipe automatic disconnect configuration has changed.

This event occurs with an application level security failure for access control.

A change has been made to the ProverModePulseWidth.

A change has been made to the ProverModePulseWeight.

Metrology parameter (PCOMP) changed.

Metrology parameter (Count Rate) changed.

Metrology parameter (Rollover Count) changed.

Metrology parameter (Initial Index) changed.

An image transfer command was initiated.

An image transfer command was canceled.

An image transfer command was canceled but was not successful.

The process to verify an image has begun.

The image verification process was successful.

The image verification process was initiated, but was not successful.

The image activation process was initiated.

The image activation process was successful.

The image activation process was initiated, but was not successful.

A change has been made to the CompressedLoadProfile object capture_period.

The meter has been calibrated.

The device has detected that its index value(s) may have become corrupted. The device should be replaced.

A change has been made to the Intelis Gas Meter's UMU calibration A2 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B1 value. This event is added to the log when the calibration completes.

A change has been made to the Intelis Gas Meter's UMU calibration B2 value. This event is added to the log when the calibration completes.